AC Input: L, N, G - 3P Terminal block

Safety block with recessed hardware insulation that will accept up to 12AWG

L= Line, N= Neutral, and G = Ground

Optional 3 wire line cord P/N: ............................... HA-LC3SZIP

AC Input Rating .................................. 90-250vac/150W/50-60Hz

    AC Input Operational ...................................... 60-264vac

AC LED Indicator (Next to AC Input Terminal Strip)

The AC indicator is a bi-color green and red led.  This LED off with AC at the terminals would indicate a blown fuse link.  A blown AC fuse link would indicate catastrophic failure and must be returned to the factory for repair.

DC VOLTAGE SELECTOR SWITCH

As marked on board, up is 24vdc and down is 12vdc.  CAUTION To prevent damage, remove DC load and battery(s) connections before switching selector switch.

DC OUTPUTS: 2P Terminal block

Note: There is up to a 10 second delay for initial turn on on SPS-6

Output voltage Nominal .....................................  12vdc/24vdc

Output Voltage full operating range .............. 9.8–13.8vdc/19.6-28vdc

Output continuous current 12v/24v ................................. 5A/3A

AC Line regulation 85-264vac ...................................  .03%Typ

Output ripple & noise at full load .................  180/50mv pp/rms Typ

Current Overload Short Circuit Protection ........................... Yes

Thermal runaway Protection .......................................... Yes

Faults are auto restart

Switching Frequency .............................................. 132KHz

All Outputs are Class II Power limiting ............................. Yes

DC LED Indicator (Adjacent to battery Header).......................  Red

SPS-6 Supervised added features:

AC Status Output Relay: 3P Terminal block

AC Fail “C” contacts rating ................................... 2A/120vac

Trouble Output: 3P Terminal block - annunciates low battery “C” contacts rating .......................................................  2A/120vac

AC Fail & Trouble are each have a three position terminal block marked “NO, C, NC” are shown in the Normal, energized, no fault condition.

Trouble battery voltage (low)............................ 12.1vdc/24.2vdc

Trouble LED Indicator ................................... On Green Normal

Battery Cutoff

SPS-6 Low Battery Cutoff Voltage ........................  9.8vdc/19.6vdc

Battery Cutoff Relay is normally energized for fail-safe operation.

Battery Charging:............................ (Header plug marked [–Bat+])

Caution – To avoid spark, apply AC before connecting battery cable to battery.

The battery charger is precision set to float charge 12V or 24V sealed or wet lead acid batteries.  Two 12V batteries are connected in series for 24V.  A 15” battery cable assembly is provided that plugs from module to battery.  Red (+) 12vdc, Black (–) Neg.

Optional 36” battery cable (1) P/N: ..........................  WA-36IBAT

Battery(s), any type of lead acid .........................  12v 4AH-40AH

      UL evaluated .................................................  7AH

Battery(s) recharge .........................................   400ma max

Battery typical charge voltage 12V/24V ................ 13.65Vdc/27.30Vdc

Battery(s) average recharging current rate ........................ 250ma

Battery(s) PTC self resetting Circuit Breaker .................... 6A PTC

Battery(s) Reverse hookup protection ................................ Yes

To estimate the recharge time in hours for depleted battery(s), multiply the AH rating times 4 (AH x 4).  As an example, a 24v system with two depleted 12v 7AH batteries would take about 28 hours to re-charge.  See http://www.securitypower.com/an3batby.pdf for battery standby selection table.

Environmental:

Humidity .......................................... 95% RH Non Condensing

Ts Storage Temperature ....................................  -40oC – 85oC

Ot Operating Temperature Range 100% rating:

      Ot Power module only ................................... -20 – 44oC

      Ot with E-89 Enclosure on wall ........................  -20 – 33oC

      each 3% load reduction increases Ot by ....................... +1oC

Over temp shut down Mosfet Jt Temp ................................ 150oC

Mechanical characteristics:

SP/SPS-6B Module Dimensions ......................   6.05”Lx3.87”Wx2.28”H

Height includes 7/16” standoffs, not provided with module.

Mounting Holes Center to Center ........................  4.50”W x 3.41”H

SPS-6B module only Weight ........................................ 12.4oz

SPS-6E (SPS-6B in enclosure) ........................... 14” x 9” x 3.50”

SPS-6E (with enclosure) Weight .................................  6.85Lbs

Approvals:

SP-6B & SP-6B meets safety ............................  UL1950 & EN60950

SPS-6 and all of its accessories are UL Listed US and C for Access Control & Burglar alarm systems UL294, UL603 & I:C5302

RoHs Lead Free