DCPM-3 Series 3 Amp

DCPM-3-A   5-28VDC Adjustable DC Power Supply module

LP-3-12   12VDC 3A Power Supply/Charger module

LP-3-24   24VDC 3A Power Supply/Charger module

LP-3ESX12   DCPM-3-12, TX-16100, in 8”x9” Enclosure

LP-3EX24   DCPM-3-24, TX-24100, in 14”x9” Enclosure

LP-3EX12   DCPM-3-12, TX-16100, PDM-4, in 14”x9” Enclosure

LP-6EXDP  12v 3A, TX16100, 24v 3A, TX24100, in 14”x9” Encl.

 Features:

• Up to 3 Amps of Continuous DC Output Current

• 12v & 24v models have battery charger with instant Transfer to Standby

• Clean Linear Power

• Electronically Protected Against

• Over Current and Temperature

• Precise Output Regulation

• Input and Output are Surge Protected

• Input can be low AC or DC volts

• Multiple units may be connected in Parallel for Higher Output Current

• Available as a module or mounted in any one of our Enclosures with any of our transformers and accessions

• Quality Manufactured in the USA with a Life time warranty

The DCPM-3 series power supplies are a versatile series of 3 Amp linear power supplies that are clean, well regulated with protected against overheating, over current, and reversed battery connection.  This clean performance allows these power supplies to power the most sensitive electronic devices.  The DCPM-3-A is adjustable from 5-28VDC that can be used as a universal supply to power a wide variety of devices requiring up to 3 Amps.   The LP-3-12, 12v and LP-3-3-24, 24v are fixed power supplies with Battery Chargers that can provide uninterruptable low voltage power with the appropriate lead acid battery(s).  The lead acid batteries may be any AH capacity you require from 4AH to 100AH depending on your standby requirements.  The LP-3 battery charger will  Precisely charge a Sealed, Gel, AGM, or flooded Lead Acid Battery(s).  The LP-3’s with battery charger have a 4A auto resetting PTC Circuit Breaker between the Battery and the DC output to protect against over current.

To test the LP-3’s with standby batteries.  It is recommended that on a regular basis, the output should be checked for proper voltage and current while the AC power is disconnected.

Because these power supplies are a linear device that must dissipate all of the power between the input and the output please review the output current graph below to be sure your input voltage, output voltage and load current comply.

Input AC Transformer

Terminals 1 & 2 identified by  .................................   IN

LP-3-12 12vdc at 3A DC Output  ................... 14 – 18vac at 80VA

LP-3-24 24vdc at 3A DC Output  .................... 24-28vac at 100VA

DCPM-3 AC or DC .................................  5 – 28vac at 100VA

  Input, Output, & Load current must comply with graph

AC LED Indicator .......................................... Green LED

DC LED Indicator ............................................ Red LED

DC OUTPUT

Terminal 3 & 4 identified by  ................................   -DC+

DC Output voltage Nominal  .....................    12vdc/24vdc/5-28v

Output voltage typical  .................   13.65vdc/27.30vdc/5-28vdc

DC Current maximum continuous rating   .......................   3.0A

If charging standby Battery Reserve  .......................    500ma

Ripple @ 80% load  .....................................  40mv pp Typ

Short circuit current limiting  ...............................   Yes

Thermally Protected  ..........................................   Yes

1 year long term Stability  ...............................    .03VDC

Battery Charging: LP-3-12 & LP-3-24

(Header plug marked [–Bat+])

The battery charger is precision set to float charge 12V or 24V Sealed, Gel or wet lead acid batteries.  Two 12V batteries are connected in series for 24V.  A 12” battery cable assembly is provided to connect the module to a battery.  Red (+) 12vdc, Black (–) Neg.

Optional 12” cable assembly for connecting two 12v batteries
in series for 24volts  .......................................   24SW

Optional 36” battery cable (1) P/N:   ...................   WA-36IBAT

Amp Hour capacity range  ...............................    4AH-100AH

Battery Fuse  .............................................    4A PTC

Reverse battery hookup protection  .............................  Yes

The recharge Rate = 3 – Load

Hours to recharge = Bat AH capacity /Amp Rate

To select battery(s), see standby selection table www.securitypower.com/an3batby.pdf .

Environmental:

Humidity  ...................................   95% RH Non Condensing

Ts Storage Temperature    ............................   -40oC – 85oC

Ot Operating Temperature Range 100% rating:

      Ot module only  ................................   -20oC – 36oC

      Ot mounted in Enclosure   .....................    -20oC – 26oC

      Each 3% load reduction increases Ot by:  .................  1oC

Mechanical Characteristics:

Center-to-Center Terminal Block Spacing with Wire ready
self Clamping Screws  .....................................    .375”

Module Size  ..............................   2.66”H x 2.92”W x 2.6”D

Mounting Holes Center-to-Center  ....................  1.41”W x 2.5”H

“ES” Enclosure size  ............................   8”W x 9”H x 3.5”D

“E” Enclosure size   ...........................   14”W x 9”H x 3.5”D

DCPM-3 module  .............................................    3.6oz

100va Transformer  .......................................     2.8lbs

Safety

DCPM-3 Series meets safety  .......................  UL1950 & EN60950

Lead Free RoHS compliant

 E-mail: ESD@SecurityPower.com
   Phone: (209) 229-7140
Fax:  (209) 229-7145